Suspension sag and preload: a beginner's measurement routine

Suspension setup can look like a mystery to a new rider. Adjusters have numbers on them, the manual gives a range, and the paddock is full of people who each have a different opinion. The good news is that the core of suspension setup is a simple, repeatable measurement routine. Sag is the most useful starting point, and preload is the adjustment most often used to bring a bike into the right range.

What sag tells you

Sag is the amount the suspension compresses under the weight of the bike and the rider. Measured at the front and rear, it shows how the bike sits and how much of the suspension travel is used under normal conditions. A bike with too little sag will feel harsh and may skip over bumps. A bike with too much sag can feel soft, wallow in corners and bottom out under braking or heavy acceleration.

Two types are commonly measured. Static sag is taken with the bike on its wheels and no rider, then with the rider in riding position. Rider sag, sometimes called race sag, is the figure that matters most for racing, because it reflects how the bike sits with the rider in normal riding posture.

Equipment you need

You need a tape measure or a ruler, a helper to hold the bike upright, and a way to mark the reference points. Many teams use zip ties or a marker pen to mark the fork tubes and the rear swingarm. Keep the tyre pressures at the setting you plan to race with, because a change in pressure changes the measurement.

Use the same surface for every measurement, ideally a flat, level floor. A slope or uneven ground will distort the readings and make it impossible to compare one day with another.

Measuring the front

Measure from a fixed point on the fork tube or the yoke to a fixed point on the wheel axle area or the bottom of the fork. Record the figure with the bike unloaded, then have the rider sit on the bike in full riding gear, in the normal riding position, and measure again. The difference is the front sag. Repeat the process twice more and take the average, so that one reading does not decide the setting.

Some teams find it easier to use the bike’s own sag markers if the manufacturer provides them. Use whatever method you choose and stick to it for the whole season.

Measuring the rear

For the rear, measure from a fixed point on the swingarm or the rear axle to a fixed point on the bodywork or the seat, then repeat the process with the rider on the bike. The rear sag should be in the range recommended by the bike or suspension manufacturer, and any change should be made in small steps.

Check the rear wheel alignment at the same time. An offset wheel changes the measurement and can make a setup appear wrong when the cause is a chain adjustment.

What preload does

Preload is the adjustment that sets the spring’s starting tension. Increasing the preload raises the static height and reduces the amount the suspension compresses under load, which reduces sag. Decreasing the preload does the opposite. Preload is usually the first adjustment to make when sag is outside the target range, because it changes the figure without changing how the suspension damps the movement.

Turn the adjuster in small increments, measure again, and record the result. A full turn can change the sag more than a beginner expects, so it is better to make a small change, ride, and assess the feel.

Damping is a separate question

Preload sets where the suspension sits. Damping controls how fast it moves in and out. A rider who changes damping before measuring sag can end up chasing the wrong problem. Set the sag first, check the feel, and then adjust the damping in small steps if the bike still does not behave as expected.

Keep the record

Write down every measurement with the date, the track, the tyre pressures, the rider’s weight in gear and the settings used. Over a season, these records show which settings suit which conditions and which rider. They also protect the team when a setup change is questioned later.

A routine you can repeat

A beginner’s routine is simple. Measure the static sag. Measure the rider sag at front and rear, averaging three readings each. Adjust preload in small steps to reach the target range. Record the result. Ride, then assess the feel. Repeat the routine after any significant change. Used consistently, this method removes most of the guesswork from suspension setup and gives the rider a bike that behaves the same way every time they go out.